Garrett Pro-Pointer AT Z-Lynk und Kopfhörer MS-3 | Kit

199,00 € *

inkl. MwSt. zzgl. Versandkosten

Versandkostenfreie Lieferung!

Sofort versandfertig, Lieferzeit ca. 1-3 Werktage

  • 13498
Pinpointer Pro-Pointer AT Z-Lynk mit Funkkopfhörer MS-3 als Kit! Das Kit beinhaltet den... mehr
Produktinformationen "Garrett Pro-Pointer AT Z-Lynk und Kopfhörer MS-3 | Kit"

Pinpointer Pro-Pointer AT Z-Lynk mit Funkkopfhörer MS-3 als Kit!

Das Kit beinhaltet den Garrett Pro-Pointer Z-Lynk, die MS-3 Funkkopfhörer und Z-Lynk-Set (alle Stecker passend zu jedem Garrett Metalldetektor). Dieses Kit ist die perfekte Ausstattung für die finale punktgenaue Ortung von Objekte. Perfekte Ortung mit überragenden Sound. Die Z-Lynk™ Wireless Technologie ist 6x schneller als Bluetooth. 

PinPointer sind unentbehrliche Helfer für uns Sondengänger, da sie wertvolle Bodenfunde wie Münzen, Schmuck, Relikte, Fibeln und andere Edelmetalle vor groben Kratzern und Beschädigungen durch Grabungswerkzeuge durch Ihre finale punktgenaue Ortung schützen. Unter Sondengängern ist die "Möhre" die erste Wahl. Sie schwören auf den wasserdichten PinPointer mit der Top Tiefenleistung!

|  PinPointer Kit für Taucher
 PinPointer Kit für alle Einsatzgebiete

 

Wasserdicht bis 6 m

Der PinPointer ist wasserfest bis zu 6 m nach IP68. (Schutzklasse International Protection 68! Dicht gegen Staub und Berührung. Wasserdicht, denn Schutz gegen Eindringen von Wasser bei dauerhaftem und kompletten Untertauchen in Wasser ist gegeben.)

Besondere Eigenschaften des Pro-Pointer AT Z-Lynk

  • Ton- und Vibrationsalarm erhöht sich automatisch beim Annähern an das Metallobjekt
  • Ton / Vibration, ohne Ton mit Vibration einstellbar
  • LostPin Pointeralarm nach 5 Minuten
  • anspruchsvolle Umgebungen / Böden / starkmineralisierten Böden, Salzwasser
  • Punktortung mit der Gerätespitze
  • 360° Rundumdetektion
  • LED Licht zum Gebrauch an lichtschwachen Stellen
  • Kratzkante zur Durchsuchung fester Bodenbestandteile
  • automatischer Abgleich
  • schnelle Neuabstimmung
  • einstellbare Empfindlichkeit
  • automatische Abschaltung
  • Tiefenmarkierung in cm / inch
  • in 3 Stufen verstellbare Empfindlichkeit
  • auffallende Gehäusefarbe, gute Erkennung im Wasser

Technische Spezifikationen des PinPointers

  • Befestigungsmöglichkeit
  • Gürtelhalter ist Teil des Lieferumfangs
  • Betriebstemperatur: - 20°C bis 54°C (-4°F to 130°F)
  • Arbeitsfrequenz: 11,5 kHz
  • Bedientasten: EIN / AUS Druckknopf
  • Länge: 22,9 cm, Breite: 3,8 cm bis zu 2,2 cm spitzzulaufend
  • Gewicht: 0,2 kg mit Batterie
  • 1 x 9 Volt Batterie (inkl.)

 garrett-ms-3

MS-3 Funkkopfhörer 

Der neue Garrett MasterSound-3  Funkkopfhörer ist kabellos und arbeitet mit einem Z-Lynk™ Transmitter zusammen. Ab AT MAX ist ein Transmitter im Detektor verbaut, sonst benötigt es eine Transmitter-Schnittstelle. Die Z-Lynk Technologie ist 6 x schneller als USB.

Die Lautstärke ist am Kopfhörer regelbar. Der MS-3 hat ein weiches Kopfband und komfortabl gepolsterte Hörmuscheln. Über einen USB Anschluss ist es einfach aufladbar und lässt sich klein zusammenfalten.

Technische Details des MS-3

  • Lautsprecher Impedanz: 8 Ohm
  • Frequenzgang: 30 - 18.000 Hz
  • eingebauter Z-Lynk™ Wireless Reveicer

 

Lieferumfang Pro-Pointer AT Kit Z-Lynk mit Funkkopfhörer

  • Garrett Z-Lynk Set mit allen Steckern passend zu jedem Garrett Metalldetektor
  • Garrett Funkkopfhörer MasterSound 3 mit USB-Ladekabel
  • Garrett AT Pro-Pointer Z-Lynk
  • Bedienungsanleitungen

 

Schauen Sie auch unsere Special Prices ...

special-price-metalldetektor-shop

 

Überblick » Pinpointer 

Pinpointer von » Garrett | » Fisher | » Quest | » Minelab | » Nokta | Makro | » XP

Metalldetektor Einsatzgebiete » Einsteiger | » Fortgeschrittene | » Profis | » Goldsucher | » Taucher | » Archäologen | » Kinder | » Strandsucher | » Tiefensucher

 

» Wireless Z-Lynk Technologie » Vergleichstabelle zwischen Garrett ProPointer AT Z-Lynk,... mehr

» Wireless Z-Lynk Technologie

» Vergleichstabelle zwischen Garrett ProPointer AT Z-Lynk, ProPointer AT und ProPointer 2

Vergleichstabelle zwischen dem  Garrett ProPointer AT Z-Lynk, ProPointer AT und ProPointer 2 in Bezug auf technische Eigenschaften, Funktionen und die größten Unterschiede.

Features ON/OFF, Retune, Adjust Button Pinpointing Tip 360° Side-Scan Area Exclusive... mehr

Features

  • ON/OFF, Retune, Adjust Button
  • Pinpointing Tip
  • 360° Side-Scan Area
  • Exclusive Scraping Blade LED Flashlight
  • Waterproof Speaker
  • Lanyard Attachment Loop
  • Sealed Battery Cover
  • Ruler in Inches and Centimeters
  • Internal Wireless Transmitter

propointer-at-z-lynk-freigestellt

Powering On

Press and release the button while holding the detector away from any metallic objects. You will hear 2 beeps and the LED will remain on.

Powering Off

Press and hold the button for a half second until you hear a single beep (or single vibration in Silent Mode), indicating power down.

Changing Settings

The Pro-Pointer AT Z-Lynk has three Sensitivity settings and two detection settings: Audio-plus-Vibrate or Vibrate-only (silent). To enter adjustment mode, press and hold the button for 2 seconds—indicated by a single beep followed by a dual-tone beep and flashing LED.  (Note: In Silent Mode, beeps are replaced by vibration pulses.) The first button press after entering adjustment mode indicates the current setting. Repeatedly press the button to cycle through the 6 settings:

1 beep    =  minimum Sensitivity, with audio
2 beeps  =  medium Sensitivity, with audio (Default) 3 beeps = maximum Sensitivity, with audio
1 vibrate  =  minimum Sensitivity/Silent
2 vibrate  =  medium Sensitivity/Silent
3 vibrate  =  maximum Sensitivity/Silent

To exit adjustment mode, press and hold the button for 2 seconds—indicated by a dual-tone beep (dual vibrate in Silent Mode), or wait 5 seconds for automatic exit.

Notes:

Lower Sensitivity settings are recommended to prevent detection of highly mineralized grounds.

Detection remains operable during the adjustment mode.

Settings will be remembered when the unit is switched off and back on.

Wireless Operation

Reconnecting:  Once paired, the pinpointer will instantly reconnect to the last paired receiver. The receiver must be powered on first. The pinpointer’s external audio will switch off when paired.

Pairing: This product can be be paired wirelessly with any Garrett Z-Lynk receiver using the following steps.

  1. First, switch on the receiver (i.e. Garrett MS-3 Wireless Headphones or  Garrett WR-1 Z-Lynk device).
  2. Hold the pinpointer within 6 inches (15cm) of the headphone or the WR-1 device.
  3. Switch the pinpointer on and wait (approximately 3 seconds) for the light on the headphones (or WR-1) to go from blinking to steady.
  4. If the units do not pair, switch the pinpointer off and then on again. Note: If you have trouble pairing, make sure that the receiver is on first,  and that the two devices are within six inches of each other. Also, be sure that a previously paired headphone or WR-1 is not powered on in  the vicinity (20 to 50 feet).

Fast Retune for Mineralized Ground

To tune out the detection of saltwater, wet sand or highly mineralized ground, hold the tip of the Pro-Pointer AT Z-Lynk to the water, sand or soil and quick-press the button for an instant Retune.

If necessary, repeat this Fast Retune to further eliminate any environmental response. Note: An alternate means of eliminating the ground response is to reduce Sensitivity.

Precisely Pinpointing Large Targets

Slowly scan toward the object until the response increases to full/constant alarm. Then quick-press the button to instantly retune and narrow the detection field. Continue scanning toward the object to find its precise location. Repeat this Fast Retune to further narrow detection field as needed.

Lost Pinpointer Alarm

After 5 minutes of being ON without a button press, the Pro-Pointer AT Z-Lynk will begin emitting progressively faster warning chirps for 60 minutes. Press the power button to reset.

Auto-Off Feature

After one hour of warning chirps, the Pro-Pointer AT Z-Lynk will power off automatically.

Scraping Blade

This rugged edge is ideal for sifting through dirt while searching for the target. The Pro-Pointer AT’s 360º-side-scan detection allows the detector to alarm when the blade is passed in close proximity to a metallic target.

Lanyard Attachment Clip

Use to attach the Pro-Pointer AT to your belt, digging pouch or your detector (if desired).

Holster

Secure to any standard size belt. A metal snap within the holster will cause the pinpointer to alarm if put away while powered on.

Ruler

The Pro-Pointer AT has a ruler molded into its exterior to measure a target’s depth in either centimeters or inches.

Low Battery Alarm

When the battery becomes low, the detector will sound an alternating dual-tone alarm. Replace the 9V battery as soon as possible.

Operational Information and Tips

  • Operation is completely automatic. All metals will be detected including ferrous and non-ferrous.
  • When a target is detected, the Pro-Pointer AT Z-Lynk will produce an audio and/or vibration alert. The rate of the pulsing audio and vibrations increase proportionately as the pinpointer is moved  closer  to a metallic target.
  • Maximum detection of very small targets is obtained against the side  about ½” from the tip.
  • To avoid cancelling out a target, do not turn on the Pro-Pointer AT while  it is adjacent to the target.
  • Because the Pro-Pointer AT is a static, non-motion detector, optimum  operation is achieved when the unit is switched off between uses.
  • Avoid using the Pro-Pointer AT as a digging or prying tool. It is designed for flat side-scanning and precise pinpointing with its tip. It is not intended to be used with excessive force.
  • For water use, do not exceed 20 feet (6 meters) depth. Make sure the battery cap threads are free of sand, sediment, etc. and that O-ring is periodically lubricated with silicone grease to maintain a tight seal.
  • Radio signals do not transmit through water, so if you will be hunting fully  submerged, you must rely upon the Pro-Pointer’s vibration and audio alerts without the benefit of headphones.
Bewertungen lesen, schreiben und diskutieren... mehr
Kundenbewertungen für "Garrett Pro-Pointer AT Z-Lynk und Kopfhörer MS-3 | Kit"
Bewertung schreiben
Bewertungen werden nach Überprüfung freigeschaltet.

Die mit einem * markierten Felder sind Pflichtfelder.

Ich habe die Datenschutzbestimmungen zur Kenntnis genommen.

Minelab Equinox 900 Minelab Equinox 900
1.249,00 € *
NEU
Leichte Gebrauchsspuren Garrett ATX Leichte Gebrauchsspuren Garrett ATX
1.679,00 € * 2.799,00 € *
Simplex+ WHP mit Nokta-Pointer Simplex+ WHP mit Nokta-Pointer
429,00 € * 569,90 € *
TIPP!
Garrett ATX Garrett ATX
2.799,00 € *
Garrett Ace Apex | VLF Sondel Metalldetektor für Einsteiger, Fortgeschrittene und Profis Garrett ACE APEX™
ab 539,00 € *